MiCOM P632
Local Control Panel with Password Protection
graphics/symbols/xh_bw.gif graphics/symbols/xh_fw.gif

The password consists of a combination of keys that must be entered sequentially within a specific time interval. The “left”, “right”, “up” and “down” keys may be used to define the password and represent the numbers 1, 2, 3 and 4, respectively:

graphics/xhelptemp/svg2png/svg_0073.png

The password can be changed by the user at any time. The procedure for this change is described below. The starting point is the factory-set password.

 

Control Step / Description

Control Action

Display

Step 0

In the menu tree “Par/Conf/LOC”, select the LOC: Password setting.
 
 
Par/Conf/LOC
Password
********

Step 1

Press the ENTER key. Eight asterisks (*) appear in the fourth line of the display.
graphics/xhelptemp/svg2png/svg_0255.png
 
Par/Conf/LOC
Password
********
********

Step 2

Press the “left”, “right”, “up” and “down” keys to enter the valid password. The display will change as shown in the column on the right.
graphics/xhelptemp/svg2png/svg_0259.png
 
Par/Conf/LOC
Password
********
*
 
 
graphics/xhelptemp/svg2png/svg_0260.png
 
Par/Conf/LOC
Password
********
 *
 
 
graphics/xhelptemp/svg2png/svg_0257.png
 
Par/Conf/LOC
Password
********
  *
 
 
graphics/xhelptemp/svg2png/svg_0258.png
 
Par/Conf/LOC
Password
********
   *

Step 3

Now press the enter key. The LED indicator labeled EDIT MODE will light up. The third line shows an underscore character ( _ ) as the prompt for entering a new password.
graphics/xhelptemp/svg2png/svg_0255.png
graphics/xhelptemp/svg2png/svg_0261.png
 
Par/Conf/LOC
Password
_

Step 4

Enter the new password, which in this example is done by pressing the “up” key followed by the “down” key.
graphics/xhelptemp/svg2png/svg_0257.png
 
Par/Conf/LOC
Password
*
 
 
graphics/xhelptemp/svg2png/svg_0258.png
 
Par/Conf/LOC
Password
**

Step 5

Press the enter key again. Asterisks appear in the third line, and a cursor (underscore) in the fourth line prompts the user to enter the new password again.
graphics/xhelptemp/svg2png/svg_0255.png
 
Par/Conf/LOC
Password
**
_

Step 6

Re-enter the password.
graphics/xhelptemp/svg2png/svg_0257.png
 
Par/Conf/LOC
Password
**
*
 
 
graphics/xhelptemp/svg2png/svg_0258.png
 
Par/Conf/LOC
Password
**
**

Step 7a

Press the ENTER key again. If the password has been re-entered correctly, the LED indicator labeled EDIT MODE goes out and the display appears as shown on the right. The new Password is now valid.
graphics/xhelptemp/svg2png/svg_0255.png
 
Par/Conf/LOC
Password
********

Step 7b

If the password has been re-entered incorrectly, the LED indicator labeled EDIT MODE remains on and the display shown on the right appears. The password has to be re-entered. It is also possible to cancel the change of the Password by pressing the CLEAR key (see Step 8).
graphics/xhelptemp/svg2png/svg_0261.png
 
Par/Conf/LOC
Password
**
_

Step 8

The change in password can be canceled at any time before Step 7 by pressing the CLEAR key. If this is done, the original Password continues to be valid.
graphics/xhelptemp/svg2png/svg_0256.png
 
Par/Conf/LOC
Password
********